brinell
美 
英
例句
The function and mathematics model between brinell hardness and annealing temperature was established.
建立布氏硬度和退火温度之间的函数及数学模型。
Brinell or Vickers or Rockwell hardness is normally determined for product forms C and H in heat treatment condition A.
对于C型和H型钢，通常在热处理条件A下确定其布氏、维氏或洛氏硬度。
Metallic materials. Brinell hardness test. Part 2 : verification and calibration of testing machines.
金属材料.布氏硬度试验.第2部分：试验机的验证和校正
The impeller, wear plate and agitator are made of abrasive resistant 28% chrome iron (600 Brinell, 57 Rockwell C).
设备中的叶轮，耐磨板和搅拌器全部采用耐磨的28%的铬铁制作。
Metallic materials. Brinell hardness test. Part 3 : calibration of reference blocks.
金属材料.布氏硬度试验.第3部分：标准试块的校正
At room temperature Brinell hardness (HB) of extruded alloys were over 80.
挤压变形合金的室温布氏硬度（HB）都超过了80。
Static test methods including Brinell, Rockwell, Vickers, Knoop, Wechsler, such as Pap.
静态试验方法包括布氏、洛氏、维氏、努氏、韦氏、巴氏等。
Calibration of standardized blocks to be used for Brinell hardness
标准布氏硬度块的标定
Research of the Correspondence Theorem Apply to Brinell-hardness and Diamond Penetrator-hardness Testing
探讨相似定律在布氏和维氏硬度试验中的应用
test values can be converted to magnitude, Brinell, Rockwell, Vickers hardness;
可将测试值转化为里氏、布氏、洛氏、维氏硬度值；
Metallic materials - Brinell hardness test - Calibration of reference blocks
金属材料.布氏硬度试验.标准块材的校准
Metallic materials - Brinell hardness test - Verification and calibration of Brinell hardness testing machines
金属材料.布氏硬度试验.布氏硬度试验机的鉴定和校准
Brinell Hardness Number Blank , Block Bottom Bearing Break Bracket Broach Brass Bronze Basic
底部轴承破裂支架钻孔黄铜青铜棕色&形状基本的套管
Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks; example of design of reference blocks
金属材料.布氏硬度试验.第3部分：标准试块校验.标准试块设计样品
Metallic materials - Brinell hardness test - Test method
金属材料.布氏硬度试验.试验方法
Brinell hardness number Battery Limit Battery Line Bill of Loading Blind Black Blank
盲板黑色空白基准标志弯矩界区界区线载荷数据表
Introduction of 2002 Edition National Standard of Metallic Materials-Brinell Hardness Test
介绍2002版金属布氏硬度试验国家标准
Standard Test Method for Brinell Hardness of Metallic Materials
金属材料布氏硬度的标准试验方法
Verification of Brinell hardness testers
布氏硬度计的检验
Test methods for bare wires--Hardness test--Brinell hardness test
裸电线试验方法硬度试验布氏法
metallic materials - test method of brinell hardness
金属材料-布氏硬度测试方法
standardized blocks of brinell hardness
布氏硬度标准扁
Analysis and elimination of errors in Brinell-hardness test
布氏硬度试验误差分析及排除
hammering type Brinell hardness tester
锤击式布氏硬度计
Under normal circumstances, sealed with 45 sets of quenched and tempered steel processing, Brinell hardness of 240 or above;
一般情况下，密封套采用45钢调质处理，布氏硬度达到240以上；
Metallic materials - Brinell hardness test - Part 1: Test method
金属材料.布氏硬度试验.第1部分：试验方法
radial arm Brinell hardness tester
摇臂布氏硬度试验机
