carburizing
美 
英 ['kɑːbjʊraɪzɪŋ]
英汉解释
例句
Steel for carburizing is usually a low-carbon steel of about 0. 15% carbon that would not in itself responds appreciably to heat treatment.
用于渗碳的一般是含碳量约为0.15%、本身不太适合热处理的低碳钢。
Carry out a research into the application of bipolar thyristor to the carburizing furnace control system.
对双向晶闸管在渗碳炉控制系统中的应用进行了研究。
CYCLE TIME : Amount of time product spends in a furnace at specified temperature for the purpose of carburizing or hardening product.
周期：产品在炉中某特定温度下渗碳或硬化所需要的时间。
The feature of the microstructure of the silicon- aluminizing coating and its anti-carburizing property were analyzed and studied.
分析了铝硅共渗层的组织特点，研究了处理层的抗渗碳性能。
The amount and the depth of carburizing on the casting surface can be obtained approximately by a calculating formula.
给出了铸件表面增碳大小及增碳层深度的近似计算公式。
Low temperature plasma carburizing is an effective process of improving mechanical property of austenitic stainless steel.
低温离子渗碳处理是一种能改善奥氏体不锈钢表面力学性能的有效方法。
Carburizing, cyaniding, and induction hardening are some of the processes commonly used to produce the case hardening effect.
碳化、氰化、感应淬火是局部淬火中经常使用的处理方法。
The carburization rate can be increased 20% compared with the conventional carburization process by using RE catalyzed carburizing.
采用改进型稀土催渗剂进行渗碳后，与常规渗碳工艺相比提高渗碳速度20%；
Meanwhile the carburizing speed is increased, the metallurgical structure is improved, the satisfactory results are obtained.
同时提高渗速、改善金相组织，取得满意效果。
The better technological process now is the step control of carbon potential during carburizing .
目前最佳渗碳工艺方法，是在整个渗碳过程中对碳势进行台阶式控制。
Brick-Die After carburizing treatment (heat treatment), complete sets of mechanical dragon brick after all embalmed.
制砖机模具经过渗碳处理（热处理），成套金龙制砖机械全部经过防腐处理。
and then carrying out molding and pre-sintering, carrying out mechanical press-fitting and the sintering-soldering, and finally carburizing.
接着进行成形和预烧结，然后进行机械压配和烧结焊，最后进行渗碳即可。
Nonsymmetrical carburizing may also contribute to distortion.
渗碳的不对称也可能导致变形。
The gear reducer for high strength steel carburizing, carburizing hardening, low noise transmission.
减速器的轮为高强度渗碳钢，经渗碳淬火处理，传动噪音低。
The results show that the carburizing hardening and high frequency induction hardening can debase the profile accuracy by about 25%.
研究结果表明：渗碳淬火和高频感应淬火对齿形精度误差的影响都在25%左右；
Pack carburizing consists of placing the parts to be treated in a closed container with some carbonaceous material such as charcoal or coke.
固体渗碳的方法是将要处理的零件与木炭或焦炭这些含碳的材料一起放入密闭容器。
RE- Carburizing test with solid powder rare earth accelerant in the sealing box multi-purpose furnace was in progress.
采用固体粉末状稀土催渗剂在密封箱式多用炉中进行了C+Re共渗试验。
It can be quenched in a controlled atmosphere, thin carburizing, carbonitriding heat treatment process.
它能在可控气氛下进行淬火，薄层渗碳、碳氮共渗等热处理工艺。
The residual life of the tubes is estimated based on the carburizing damage analysis.
在考虑渗碳损伤的前提下对炉管的剩余寿命进行了评估。
A new forge residual heat isothermal normalizing technique for alloy carburizing steel is put forward.
针对合金渗碳钢锻（轧）件，研发了一种新的利用锻造余热等温正火热处理工艺。
Two carburizing processes were adopted, before or after the hydrothermal reaction.
进行了水热前和水热后两种渗碳工艺研究。
The furnace atmosphere was calculated under the condition of carburizing in the nitrogen-methanol based atmosphere in this paper.
本文是采用氮、甲醇基渗碳气氛渗碳，对炉内气氛进行计算。
The method of eliminating carbon can solve availably carburizing defect of steel casting was proved by practical production.
实践证明这种工艺方法可有效地解决铸钢件的增碳缺陷问题。
The sample of carburizing makes the component and hardness analysis.
对渗碳后的试样停止了成分和硬度剖析。
This article recommends the process of direct quenching after carburizing for sucker rod pump liners.
介绍了抽油泵衬套渗碳后直接淬火处理工艺。
The low-temperature RE carburizing technology is explored by a series of tests.
通过一系列试验，摸索出利用稀土低温渗碳技术。
Effect of silicon on microstructure and properties of meta-bainitic carburizing steel were studied.
研究了硅对准贝氏体渗碳钢渗碳组织与性能的影响。
So RE slat liquid carburizing may replace poisonous cyanide slat bath or "603" slat liquqid carburizing.
可取代剧毒的氰盐和微毒的“603”盐浴渗碳。
Direct quenching after carburizing can meet technical requirement in order to save working time and cost.
为节省工时和成本，渗碳后采用保护性气氛加热直接淬火可以达到技术要求。
repeatedly forged iron, based on ancient block of iron also find the experience of carburizing Cheng Gang, this is the first steel to steel.
在反复锻打铁块的基础上，古人又找出块炼铁渗碳成钢的经验，这种钢地就是最早的钢。
Pressing bolt from the steel by carburizing treatment, enhance the surface hardness and wear resistance;
榨螺由合金钢经渗碳处理，增强表面硬度和耐磨性；
Study of Plasma Carburizing Process for Stainless Steel and Microstructure and Mechanical Properties of the Carburizing Layer
不锈钢等离子渗碳工艺及渗层组织和性能的研究
Design for hardening press die of outer races of double row tapered roller bearing made of carburizing steel
渗碳钢双列圆锥滚子轴承外圈淬火压模设计
Study of the Are-added Glow Discharge Plasma Non-hydrogen Carburizing on Titanium Alloy Surfaces
加弧辉光离子无氢渗碳在钛合金表面上的应用研究
Design and Adjusting of Nitrogen-Based Atmosphere Carburizing Process for a New Mult-Purpose Chamber Furnace
新箱式多用炉氮基气氛渗碳淬火工艺的设计与调试
Conditional stability and efficiency of the finite differential method in the carburizing mathematical model
渗碳数学模型差分算法的条件稳定性和有效性
Research and Application of Microcomputer Controlled Gas Carburizing with Chamo Electrical Resistance Method
差模电阻法微机控制渗碳仪的研制及应用
RE-Carburizing Technology Used for Gear
齿轮稀土碳共渗工艺
Study on the Corrosion Resistance of the Arc-added Glow Discharge Plasma Non-hydrogen Carburizing on Titanium Alloy Surface
钛合金表面加弧辉光离子无氢渗碳耐蚀性能的研究
Search for Distortion Law of Carburizing and Quenching Parts by Statistical Method
用统计法寻找渗碳淬火变形规律
