cylindricity

cylindricity

美 [sɪlɪnd'rɪsɪtɪ] 　英 [sɪlɪnd'rɪsɪtɪ]

• n.圆筒度
• 网络圆柱度；园柱度；柱面度

英汉解释

n.

1. 圆筒度

例句

The cylindricity error can be got by optimization. The results show that this method can get cylindricity error without damage and touch.

实验结果表明，该方法可以在无接触无破坏的前提下得到较为准确的测量结果。

Then the edge points of the pipe are extracted by Facet model. The cylindricity error can be obtained by the least square cylinder.

在已知所有边缘点信息的基础上采用最小二乘圆柱法求得管道的圆柱度误差。

The cylindricity error separation and reconstruction method proposed in this paper was systematically verified.

利用自律验证法对本文提出的圆柱度误差分离及重构方法系统地进行了实验验证。

Cylindricity error is defined as the changes between measured column and ideal column.

圆柱度误差是指实际被测圆柱面对其理想圆柱的变动量。

Based on industrial CT, this dissertation studied the cylindricity error evaluation and inner surface display of pipeline.

本文以工业CT为基础，研究了工件内部管道的圆柱度测量与内表面显示算法。

The experimental results show that the roundness is improved by 40% and cylindricity by 23% after compensation.

实验结果表明，补偿后的工件圆度误差平均改善了40%，圆柱度误差平均改善了23%。

Because of the limit of measuring tools, the traditional methods can not evaluate the cylindricity error of internal pipe.

由于测量工具的限制，传统方法对无法充分接触的内部管道的圆柱度难以测量。

While the plane is measured by using the cylindricity measuring instrument and square, the data acquisition should be done at the same time.

首先利用圆柱度仪和角尺对被测件进行测量，同时采集原始测量数据，然后利用最小二乘法实现平面度误差的评定。

Study on Measurement of Cylinder's Taper and Run-out on Cylindricity Measuring Instrument

圆柱度仪测量圆柱体锥度及跳动的研究

Establishment and Solution of Mathematical Evaluating Model for Linear Programming of Cylindricity Error

圆柱度误差评定线性规划模型的建立与求解

Method for Cylindricity Errors Evaluation Using Particle Swarm Optimization Algorithm

基于粒子群算法的圆柱度误差评定方法

The New Arithmetic of Cylindricity Error and Its Application in Micro computers

圆柱度误差新算法及其在微机上的实现

Optimization of Cylinder Bore Honing Platform Structure and Improvement of Cylindricity

缸孔平台结构的优化及圆柱度的改善

Analysis of the Cylindricity Tolerance and Press Mounting Curves of Axle Wheel Seat and Wheel Hub Bore

关于车轴轮座、车轮轮毂孔的圆柱度公差和压装曲线分析

A Practical Algorithm for Computing Cylindricity Error in the Rectangular Coordinates

直角坐标系下计算圆柱度误差的一种实用算法

Research on Virtual Cylindricity Error Measuring Instrument

虚拟圆柱度误差测量仪的研究

Cylindricity Error Evaluation Based on an Improved Genetic Algorithm

基于改进遗传算法评定圆柱度误差

Measurement techniques of cylindricity with three-point method

圆柱度的三点法测量技术

Error Separated Method of Measuring Datum for Cylindricity Measurement

一种圆柱度测量基准的误差分离方法

Application of DNA Computing Model to Cylindricity Error Evaluation

DNA计算模型在圆柱度误差评定中的应用

Application of laser measuring method on detection of cylindricity error

激光测量法在圆柱度误差检测中的应用

The measuring cylindricity error with precision and non-touching method

圆柱度误差的非接触精密测量方法

The Minimum Area Principle of Computing Methd's Research for Data Processing of Roundness Cylindricity and Coaxality

圆度、圆柱度和同轴度计算机测量数据最小区域法处理算法研究

Optimization Evaluation of Cylindricity Error Based on Correctional Simplex Method

基于修正单纯形法的圆柱度误差优化评定

Analysis of several cylindricity measurement models based on error separation technique

基于误差分离技术的几种圆柱度测量模型分析

Data Processing in Testing Cylindricity Error

圆柱度误差检测中的数据处理

Accurate Assessment of Departure from Roundness and Cylindricity Based on the Optimal Control

基于最优控制的圆度圆柱度误差精确评定

Method of error separation based on photoelectric Sensor in measurement of cylindricity

圆柱度测量中基于光电传感器的误差分离方法

On-Line Cylindricity Measurement Based on Wavelet Harmonic Analysis

一种基于小波多频分析的圆柱度在线检测方法

Calculating method of cylindricity error based on immune algorithm

基于免疫算法的圆柱度误差的测量

A Novel Method and Technology for Cylindricity Errors Separation

一种新的圆柱度误差分离方法和技术