extrudate

extrudate

美 　英 [ɪks'tru:deɪt]

• n.挤出物；挤条产品
• 网络压出胶；压出物；挤制材料

英汉解释

n.	1. 挤出物 2. 挤条产品

例句

Nitrogen is also used to prevent oxidation, but take care not to blow too hard or cool the die so much that it distorts the extrudate.

也可以用氮气防止氧化，但是要记住，不要吹得太过火，否则会将口模过分冷却，这样会导致挤出物变形。

The extruder used for this process features simple head structure, low price I less space and quality extrudate.

该法使用的挤出机，具有机头结构简单、价廉、占地面积小，挤出物质量好等优点。

The defect of extrudate in the extrusion process in the form of melt fracture could only be evidenced in the semisolid state of PP melt.

在挤出过程中，以熔体破裂形式出现的挤出物的缺陷只有在PP熔体处于半固体状态时才能观察到。

Tri-screw extruder should not be applied to the extrudate which should be dealed within a short reactive time.

对反应时间不宜过长的聚合物，应避免使用三螺杆挤出机。

Many researches demonstrate that the processing parameters have significant effects on extrudate qualities.

大量研究表明，膨化加工工艺对产品质量有重要影响。

Experimental results indicated that: The extrudate's expansion diameter decreased with increasing PVA ratio.

实验结果显示：产品之膨发直径随PVA添加比例增加而降低。

The extrudate's physical properties measured in this study were true density, bulk density, apparent specific volume, and breaking strength.

挤压产品之物理特性包括：总体密度、眞密度、比容积以及切断强度。

The pressure gradient and velocity gradient of the extrudate in the central area were small, and the extrudate flowed . . .

中心区的物料压力梯度和速度梯度都较小，物料在中心区流动缓慢，中心区的物料粘度值较大；

Abnormity extrudate (trilobe or butterfly shape) with high crush strength and high utility ?

异型结构（三叶草或蝶型）具有高的压碎强度和有效利用率？

The effects of shear rate, relaxation time and slip length on extrudate swell ratio were investigated using simulation.

考察了体积流量、松弛时间和滑移段长度对挤出物挤出胀大比的影响。

The effect of the core pin on extrudate characteristic was little.

机筒上的销钉对挤出特性影响力很小。

Model for rod and pipe extrudate of amorphous plastics cooled in water bath is built based on heat transfer theory.

依据传热学原理，建立了无定形塑料棒状和管状挤出制品的水浴冷却模型。

Relationship Between Extrudate Swell and Entry Elastic Stored Energy in Die Flow of Tire compounds

轮胎胶料口模挤出胀大与入口弹性贮能的关系

Three-dimensional Finite Element Analysis for Extrudate Swell of Polymer Melts by Wagner Constitutive Equation

用Wagner本构方程对聚合物挤出胀大的三维有限元分析

The Extrudate Distortion and the Non-linear Viscoelasticity of Linear PE and its Copolymer Melts

线型聚乙烯及其共聚物的挤出畸变与熔体粘弹性的关系

Test Study on the Influence of Parameters of Extrusion System on Ratio of Residual Oil of De-hulled Rapeseed Extrudate

挤压系统参数对脱壳菜籽残油率影响的试验研究

Three-dimensional Computer Modeling for Extrudate Swell of Polymer Melts

粘弹性聚合物熔体挤出胀大的三维计算机模拟

The basic study on the change of yeast growth in the extrudate for ethanol

酵母在挤压膨化的酒精原料中生长变化的基础研究