hot-forging
美 
英
英汉解释
例句
To improve and stabilize the service life of hot-forging die fabricated by cast die steer, the failure modes and mechanism were analyzed.
为了稳定和提高精铸热锻的使用寿命，研究了其失效形式和机理。
After analysis of reducing the heat load's ways and means, the design method for multi-metal hot forging dies is proposed.
分析了降低热负荷的方法和途径，提出多金属热锻模设计方法。
This paper presents the development of a new type build-up welding rod used for hot forging die.
研究了一种新型热锻模堆焊焊条。
During the process of hot forging, the temperature has a great effect on the mechanical performance of the material.
温度对热锻模的力学性能有很大影响，温度的变化导致锻模失效。
Improper material composition and processing can cause earlier fracture failure and short life happened to the hot-forging dies.
不恰当的材质及工艺导致热锻模具出现早期断裂失效，失效形式不合理，寿命较低。
the thermal stress is the most fundamental failure reasons on the base of the distribution of stress field in hot forging dies.
根据应力场得出热应力是热锻模失效的最根本的原因。
The steels can obtain better strength and toughness by subsequent air cooling after hot forging or rolling without any heat treatment.
本钢种无需经过任何热处理，经锻轧后空冷就能达到较好的强韧性。
I think a radiator thermostatic valve used on the body is simple, using hot forging is very appropriate.
我认为在暖气上所使用的温控阀属于简单阀体，采用热锻是非常合适的。
The lifetime of hot forging die decreases greatly owing to softened layers brought by high thermal loadings.
热锻模寿命由于高的热载荷引起其表面层软化而大大下降。
The importance of numerical simulation of microstructure evolution during metal hot forging was introduced in this paper.
阐述了金属材料塑性加工中微观组织演变数值模拟的重要性。
And it's difficult to process. The traditional hot forging process needs big energy and has Large amount of follow-up Machining.
传统的热模锻工艺能耗大，后续机加工量大，生产成本高、缺乏市场竞争力。
The hot-forging dies made by new-type precision casting die steel are applied on site.
采用新型精铸模具钢制备热锻模并进行现场应用。
The problems in cast technologies of hot-forging dies are pointed out and suggestions are presented.
指出了精铸热锻模具制造中存在的成型问题，并提出了建议。
A precise spray forming device for hot forging dies was designed and fabricated based on spray forming principles.
基于喷射成形基本原理设计了热锻模精密喷射成形装置，阐述了其关键技术及模具成形特点。
The application status of precision cast hot-forging dies in the world are summarized.
简述了精铸热锻模具国内外应用状况，对铸造模具钢的研究进展进行了研究。
Hot forging, rolling, extrusion, etc.
热锻、滚轧、热压等等。
Simulation Analysis for Effects of the Parameters on the Surface Temperature of a Hot Forging Die
工艺参数对热锻模表层温度的影响模拟分析
Development of Build-up Welding Rod Used for Wear-Resistance and Cold-Heat Fatigue Resistance Hot Forging Die
热锻模耐磨耐冷热疲劳堆焊焊条的研制
Heat Treatment Technology for Increasing Service Life of Hot Forging Die of Bearing Rings
提高套圈热锻模使用寿命的热处理工艺
Application and Improvement of Service Life of Hot-forging Dies Prepared by Cast Steel
精铸模具钢热锻模的应用及寿命的提高
Rigid-Plastic Finite Element Method Analysis of the Thermodynamic Couple in Hot Forging Forming Process
热锻中的变形-传热耦合刚塑性有限元模型的建立
Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging
后热锻用微合金，高质量，热锻钢棒的标准规范
The Technological Parameter Optimization of Gear Billet Hot Forging Process with Damage Minimization
基于最小损伤值的齿轮毛坯锻造成形过程工艺参数优化设计
Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging
特殊质量微量合金热锻钢棒规范.后续热锻件规范
Reverse Copying and Amendment of Tool Electrode for the Electrochemical Machining of Hot Forging Die
热锻模电解加工工具电极的反拷和修正
Numerical simulation and microstructure prediction for hot forging process
热锻工艺数值模拟及微观组织预测技术
Numerical simulation of microstructure evolution of flange axle during hot forging
法兰轴热锻过程中的微观组织演变的数值模拟
Microstructure simulation in hot die steel after hot forging and simulation software design
热作模具钢锻后组织模拟及软件设计
Review of numerical simulation for the cooling process of the structural steel hot forging
结构钢热塑性变形后冷却过程的数值模拟研究综述
The Invalidation Analysis and Strengthen Treatment of Hot Forging Die for Automobile Gears
汽车齿轮胎热锻模失效分析及强化处理
Methods Improving Service Life of Hot Forging Die
提高热锻模具使用寿命的方法
Cast Technologies and Its Application in Hot-forging Dies
精铸热锻模具的成型方法及应用
Failure Analysis on Anomalous Split of Combination Hot-forging Dies for Engine Valves
组合式气门锻模非正常开裂失效分析
Research of quality control and process optimization of gear billet hot forging
齿轮毛坯锻造成形内部质量控制与工艺优化设计
Improvement of Heat Treatment Process of the Hot Forging Dies for Connecting Rod
连杆热锻模的热处理工艺改进
Selection of Tempering Technology of New Cast Die Steel for Hot Forging
新型铸造热锻模钢回火工艺的选择
Numerical Simulation of crankshaft in hot forging procedure
曲轴锻造过程的数值模拟
The Hot Forging-Cold Forging Combined Plastic Forming Technology
热锻-冷锻复合塑性成形技术
Numerical simulation of Fore closure in solid cylinder under hot forging
圆柱体内部空洞热锻闭合过程的数值模拟
Alloying Design and High-temperature Wear Property of Cast Hot-forging Die Steel
精铸热锻模具钢的合金成分设计及其高温磨损性能研究
