machinability
美 [məˌʃɪnə'bɪlətɪ] 
英
- n.机加工性能；切削性能
- 网络可切削性；机械加工性；可加工性
英汉解释
例句
This method has been used to analyze the machinability ranks for the compound oxide ceramics containing lanthanide pho. . .
通过对含稀土磷酸盐的氧化物复合陶瓷材料的可加工性等级分析，证明该方法是可行的。
The machinability of a new type material used for the roll-sleeve in the transnormal roll casting of aluminum alloys was researched.
对新型铸轧辊套材料的切削加工性能进行了综合分析；
This process can effectively eliminate chilling, improve mechanical properties and machinability, as well as realize effective filtering.
这种方法能有效地消除白口，改善力学性能和铸铁的加工性能，同时又能提供有效的过滤。
In terms of resources, price, foundry properties and machinability, cast iron is superior.
铸铁具有资源、价格和铸造、切削工艺优势。
Characterization of sulfide shapes in structural steels with improved machinability using standard diagrams. Micrographic method.
用显微照像法显示改进机械加工性能的结构钢硫化物形状的特征。
And an approach to the evaluation in machinability of multiple attributes for complicated surface part was proposed.
提出了复杂曲面零件可加工性分析的多属性评价算法；
The made Mo-Cu material has machinability, ablation resistance, good electric conductivity and thermal conductivity.
所得到的钼铜材料具有可加工性、耐烧蚀、高电导和高热导的特点。
Tungsten and its alloy are very good materials in engineering, but their machinability is worse.
钨及其合金是非常好的工程材料熏但其切削加工性差。
The machinability of crystal material is studied, and the influence of the cutting condition on surface roughness is analyzed.
本文探讨了晶体材料的切削加工性，重点分析了切削条件对表面粗糙度的影响。
Although not used much any more, approximate machinability ratings are available in the example below.
尽管已不再大量的被使用，近乎准确的机加工率在以下的例子中能够被看到。
An excellent machinability can be obtained for the developed alloy.
所开发的合金获得了极好的切削性能。
Overall, the 800. degree. F. billet reheat for hold times less than about 5 minutes yielded the best machinability.
大体上，800？坯料再加热持续少于约5分钟的保持时间产生最好的机械加工性能。
ductility and machinability of sintered bronze oil bearings with microstructure is revealed.
揭示了烧结青铜含油轴承的显微组织和压溃强度、延展性及切削性的关系。
Research on grinding of ZTM ceramics is conducted concerning its machinability and surface roughness.
对ZTM陶瓷材料进行磨削加工，研究了其加工性能及加工后表面质量。
Vacuum quenched and air cooled steel, steel improved for SGT as to hardenability and wire electric discharge machinability.
气冷、真空淬火钢。改善了SGT的淬火性及钢丝电火花加工件。
The alloy has enhanced productivity, strength, and machinability and can be used as a direct replacement for lead containing alloy 6262 T-6.
该合金具有提高的生产率、强度和机械加工性能，并且可以被用作含铅合金6262T-6的直接替代物。
Changing the recognition of machinability for materials.
改变了对材料可加工性的认识
Machinability of cast iron, especially white cast iron, was explained.
阐述了铸铁材料尤其是白口铸铁的切削性能。
The advances in recent researches on MMCs' machinability are reviewed in this paper.
综述了国内外在金属基复合材料切削加工性及机理方面研究的进展情况。
In manufacturing plants, tool life and surface roughness are generally considered to be the most important factors in machinability.
在制造厂里，刀具寿命和表面粗糙度通常被认为是可机加工性中最重要的因素。
Copper nickel, good machinability and bad crack resistance.
镍铜，易加工，但抗裂性较差。
Machinability is a key factor in increasing productivity.
机械加工性是提高生产力的关键要素。
In addition to the tensile properties, machinability was evaluated for the extrusions.
除了拉伸性能，还对挤压件进行机械加工性能的评价。
In the end, the reason of changing of machinability was been analyzed, curve fitting was done to an. . .
最后分析了加工性能变化的原因，并对铣削力、表面粗糙度与晶粒大小的关系进行了曲线拟合。
FIG. 4 shows DSC peak area for the Tin (Sn) phase versus machinability results.
图4示出了锡（Sn）相的DSC峰值区与机械加工性能结果的关系。
From this graph, it is observed that the longer hold times and the 850. degree. F. reheat temperature are detrimental to machinability.
从该图观察到，较长的保持时间和850？的再加热温度对机械加工性能是有害的。
The Experiments on the Machinability of A New Type Material Used for the Roll-Sleeve in the Transnormal Roll Casting of Aluminum Alloys
新型铝合金超常铸轧辊套材料的切削加工性能实验研究
Quantitative Evaluation of Product Machinability under Limited Manufacturing Resources
制造资源有限情况下产品可加工性定量评价方法研究
Effect of heat treatment on the machinability and flexible strength of a novel dental mica glass-ceramic
热处理对新型牙科陶瓷可切削性及强度的影响
A Fuzzy and Comprehensive Evaluation of the Machinability for Processible Ceramic Materials
可加工陶瓷材料可加工性的模糊综合评价
Determining the Influence of Property Parameters on Metal Machinability via Analytical Grey Incidence Process
用灰关联分析法确定性能参数对金属材料切削加工性的影响
Comparison of machinability of two types of dental machinable ceramic
两种牙科切削陶瓷材料可切削性的比较
Research on plasticity and machinability of metal materials from the morphology of hardness indentation
由硬度凹坑形貌预测金属材料塑性及切削加工性
Application of Grey Theory and Uniform Design in the Research of the Machinability of Glass- Ceramics
灰色理论与均匀设计在研究微晶玻璃可切削性中的应用
Machinability of S-bearing Non-quenched-tempered Free-machining High Strength Steel Manufactured by Converter-refming-continuous Casting
转炉-炉外精炼-连铸生产的含硫非调质易切削高强度钢的切削性能
foundry products - pigs . iron - machinability testing
铸件-金属铸块.铸铁切削性试验
M Machinability Marble Mesh Microcrack Micro-flaking Microjet Mixing chamber Mixing tube Mud Multi-phase jet
加工性大理石网，筛，目微裂隙，微裂缝微剥落微射流混合腔混合管，混砂管泥浆多相射流
Development of High Refractoriness and High Machinability Stainless Steel with Mo-adding Type Applied in Automobile Exhaust Manifold
添加Mo型高耐热性和高加工性汽车排气歧管用不锈钢的开发
Machinability of powder metallurgical sintered steels
粉末冶金烧结钢的加工性
Research on Angle Parameter Design and NC Milling Machinability of Same Width Inclined Surface
等宽斜削面角度参数与数控铣削工艺性研究
