parting-line

parting-line

美 　英

• n.分型线
• 网络分模线；分膜线；相关词条

英汉解释

n.

1. 分型线

例句

If the parting line cannot be on a single plane, then it is good practice to use symmetry of the design to minimize the side thrust forces.

如果分模面不能在单一平面，利用设计的对称性来减小侧向推力不失为一种好方法。

Coining is usually done on surfaces parallel to the parting line, and little metal flow is involved in the operation.

铸币通常是做表面平行的线，与小金属流动是参与行动的。

The gate location, ejector pin location and parting line (especially cosmetic surface) must be approved by US before tooling .

入水、顶针位置以及分型线（特别是外表面）等在加工前必须得到美国确认。

The seam between them is the parting line.

两部分之间的接合处是分界线。

The drag is first filled partially with sand, and the core print, the cores, and the gating system are placed near the parting line.

先将下型箱装上部分型砂，安放好型芯座、型芯，浇通系统应放置在分型线附近。

The methods of parting direction determination, parting line and parting surface generation were presented and analyzed.

对脱模方向的自动确定、分型线和分型面的自动生成方法进行了介绍和分析；

since the draft angle was changed, we need to lower the parting line for the mold.

由于角度改变，模具分型处要降面。

2 gate, vents parting line, and ejector pin locations must be approved by XXX prior to die construction.

浇注前，浇道、排气道以及起模杆的铺设位置必须经过XXX的批准。

In this paper, a new approach to automatically searching the parting line in injection mold design is introduced.

提出了一种自动搜索模具分型线的方法。

ALL UNSPECIFIED EXTERIOR (NON-APPEARANCE SURFACE) EDGES TO BE 0. 13 MAXIMUM RADIUS, EXCEPT AT PARTING LINE.

所有未指明的外型（非外表面）边缘最大半径为0.13，分型线处除外。

parting line, the gate, cavity, core, mold insert, ejection force.

分型面、侧浇口、型腔，型芯，镶块，脱摸力。

Is the parting line locked sufficiently to prevent slippage and deflection of cavities?

分模面之锁定能否很好防止内模滑动和偏移？

REMOVE ALL FLASH AND SHARP EDGES AND PARTING LINE FLASH FROM CASTING.

从铸件去除所有闪光和锐边和分开线闪光。

The parting line or the parting surface is a line or surface that separates the cope and drag.

分型线或分型面是将上、下两型箱分开的线或面。

The parting line or the parting surface is line or surface that separates the cope and drag.

分型线或分型面是分离上下型箱的线或面。

Is parting line accepted by customer?

产品分模线客户接受吗？

4 parting line edges, flash, gates, runner, and riser extensions to be 0. 10 maximum.

分型面、飞边、浇口、浇道以及拔模斜度不超过0.

There are sharp edges if we set the parting line here, it will reduce the tool life.

如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。

forging streamline needs to the parting line B - B for overall cutting, metallographic sample blocks around the middle in stem

锻造流线需在分模线B-B处进行整体剖切，金相试块位于杆部中间部位

Automatic Determination of the Parting Line in Injection Mold Design

注塑模设计中分型线的自动确定

Computer Aided Parting Line Formation by Edges Discretization

基于边界离散的计算机辅助分型线的确定

On Automatic Searching of the Parting Line in Injection Mold Design

注塑模具分型线自动搜索技术研究

Injection mould parting line and sizing spacing parting sequence

注射模的分型面及其顺序定距分型

Automatically determining parting line in injection mold design using the finite element method

有限元方法在注塑模具分型线确定中的应用

Basic Structure Mould Type Parting Line Feeding System Mould Grade

基本结构模具类型分型面浇注系统模具等级

The parting line gate is the easiest for the pattern maker to make;

分开线门是最容易对样式制作商做；

parting line gloss printing tolerance

光彩，光泽印刷

A New Slanting Parting Line and Core-Pulling Mechanism

一种新型的斜向分型与抽芯机构

Basic structure of mould with hidden parting line for automotive trim component

内藏式分型线汽车外饰件模具的基本结构

The Parting Line and Draft of Round Plastic Parts

关于圆形塑料制品的分型面和出模斜度

Precision trim parting line within 0. 24 of true surface . maximum mismatch on parting line 0. 24

外观面的修剪分模线的精度应该0.24以内，最大的不和谐的分模线为0.