warpage
美 
英
- n.弯曲；指木材；塌腰；卷曲
- 网络翘曲；变形；翘曲度
英汉解释
例句
Possible. The part is very long and thin, very easy to be deformed ( warpage). Please inform customer about this.
很有可能会变形。产品又长又薄，很容易变形。需告诉诉客户这事。
Thus, the semi-insulating nitride semiconductor crystal substrate in which warpage is less and cracking is less likely can be obtained.
由此，能获得其中翘曲较少且较不可能发生破裂的半绝缘氮化物半导体晶体衬底。
c. Mold stress relief : No shrinkage, warpage or other distortion to interfere normal operations or reduce electrical spacing.
残留应力：不会缩收、扭曲或其它变形而影响原有之特性或降低绝缘距离。
This indicates that the developed ANN model has good interpolation capability and can be used as an efficient predictive tool for warpage.
这表明ANN模型具有良好的插值能力，可作为一种对于翘曲预测的有效工具。
If this causes a warpage problem, it sometimes helps to raise the overall water temperature and slow the rate of heat transfer.
如果这样还有翘曲问题，那么升高总的水温并降低热交换速度是有益的。
It is revealed that the optimal method is able to effectively reduce plastic part warpage.
结果显示各最佳化方法均能有效降低塑件翘曲；
Through comparing the important simulating results about the weld lines, warpage deformation, sink marks, the best gating is received.
并通过比较不同方案下的熔接线、翘曲变形、缩痕指数等重要结果，得出了最佳的浇注系统设计方案。
In the micro-featured injection molding process, mold temperature would directly affect the shrinkage, warpage and residual stress.
具微结构与微特徵尺寸产品的射出成型制程中，模具温度控制会直接影响产品的收缩、翘曲与残留应力。
significantly improves part quality in warpage, roundness, flatness and dimensional stability, reduces molded-in stress MuCell?
可改善产品的翘曲，同心度，平面度及尺寸的稳定性和产品内应力。
GUO ZH Y. Numeric simulation and experiment research on warpage and deformation of injection molding part. [D].
郭志英。注射制品翘曲变形数字模拟及试验研究[D]。华中科技大学，2001。
Moreover, fast filling and less time for holding were also dedicated to reduce the warpage of product. . .
适当提高注射速率和减少保压时间也可减小制品翘曲。
C in the material that can lead to warpage either after the heat treating process or during subsequent machining operations.
在物质，可以导致翘曲后热处理工艺，或在随后的加工操作。
Warpage of Parts: Uneven surface temperature of the molds.
变形：不均匀的模具表面温度。
Seeing you smile, the corners of the mouth gradually to warpage.
看着你笑的时候，嘴角也渐渐的往上翘。
The causes producing warpage and the effecting rules of various factors were found out and the solving methods put forward.
找到了产生翘曲变形的原因及影响规律，提出了解决的方法。
Next, inspect the gusset for warpage and straighten as needed.
下一步，检查和整顿的翘曲扣板根据需要的一面。
The shaped errors have many forms, including warpage deformation, Stair-stepping effect and so on in fused deposition modeling (FDM).
在熔融堆积成形制造中，形状误差有翘曲变形、台阶效应等形式。
Tanks shall be suitably reinforced to prevent warpage and shall use a minimum of 100 mm (4 in) structural channels for underside clearance.
坦克应适当加强，以防止翘曲和应使用100毫米（4）结构的渠道最低底面间隙。
Surface smoothness and low warpage.
表面平滑，低翘曲性。
Large thin parts can have warpage because the residual stress and strain induced during filling and packing.
大薄的部分有翘曲残馀应力与应变因为期间产生灌装。
the average mold temperature, cooling time is short, quick injection can reduce the warpage of plastic parts.
模具温度平均、冷却时间短、打针速度快可以减小塑件的翘曲变形。
It includes checking the first and last parts in a job run for signs of warpage, flashing, mold wear, and other process maladies.
这个手册包括检查我们做的第一个直到最后一个部件，以发现下述问题的迹象：翘曲、飞边、模具磨损和其它的工艺缺陷。
s Experimental relations between 2 kinds of gate and 7 kinds of processing parameters and the warpage of HDPE plate were described.
研究了两种模具、七种成型工艺参数与高密度聚乙烯平板翘曲变形之间的关系。
According to the statistical results, the injection time is the most important affecting factor on warpage.
结果表明，注射时间对注塑件翘曲变形的影响最大。
Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies
防止钢组件热浸镀锌时翘曲和扭曲用安全保护
The Analysis of the Warpage of the Thin-Wall Plastic Parts and the Optimization of the Technological Parameters
薄壳塑件翘曲变形分析与工艺参数优化
Analysis of the Warpage of the Lengthy Thin-Wall Plastic Part and Optimization of the Technological
超长薄壁塑件翘曲分析和工艺优化
Speckle projection correlation technique for measuring warpage of mobile-phone chip
投影散斑相关方法测量芯片翘曲度
Effect of Geometrical Nonlinearity on Warpage Prediction of Matrix Stacked Die BGA During Assembly Process
集成工艺中叠片BGA阵列翘曲的几何非线性预测分析
Warpage optimization and influence factor analysis of injection-molding
注塑制品的翘曲优化及影响因素分析
Application of Warpage Modified Four-node Element in One-step Forming Simulation of Certain Automobile Oil Box
翘曲修正曲面展开四节点单元在某汽车油底壳快速成形模拟中的应用
Electronic Package Warpage Simulated with Numerical Method
电子封装器件翘曲问题的数值分析
Pack speed effects the cavity pressure profile which, in turn, effects parts shrinkage and warpage;
压缩速度影响模腔压力，换言之，影响产品缩水和变形。
Error Analysis of Finite Element Numerical Simulation in the Warpage of Injection Molded Parts
注塑制品翘曲变形有限元数值模拟的误差分析
Nonlinear finite element analysis on electronic chip package warpage
芯片电子封装翘曲非线性有限元分析
Affecting factors of shrinkage and warpage of thin-wall injection molding process
注射成型薄壁制品收缩与翘曲因素
Research of Viscoelastic Warpage Analysis of Surface Mount Package
对表面安装封装体的粘弹性翘曲问题的分析
Analysis on the Warpage of Ultra - Length Protect Cap and Optimization of the Process
超长保护盖翘曲分析和工艺优化
the shape, size and location of the gate had great effects on the warpage of the plate;
模具浇口的形状、大小和位置对HDPE平板翘曲变形的影响非常大；
those having a relatively big impact on warpage include the melt temperature only;
对翘曲变形影响较大的工艺参数为熔体温度；
