asme
美 [eɛsɛm'i] 
英
英汉解释
abbr. | 1. (=American Society of Mechanical Engineers)美国机械工程师学会 |
英英解释
例句
Analysis shows that the calculated result of ASME'S method can more practically reflect the operation state of condensers.
分析表明，ASME法的计算结果更能反映凝汽器的实际运行状况。
ASME capacities are steam pressure ratings and do not reflect the CSA temperature relieving capacity of the valves for selection purposes.
ASME流容是蒸汽压力额定值，并不代表阀门在所选择的用途中CSA温度泄放能力。
This paper describes the difference between the terms of groove and bevel in weld joints and condition in ASME Code translation .
本文叙述焊接接头中术语剖口与坡口的区别和在ASME规范翻译中应注意的问题。
Suggestions for revisions or clarification to this Guide should be directed to the ASME Director, Accreditation and Certification.
为修改或澄清，以本指南建议，应直接向美国机械工程师协会董事，鉴定和认证。
ASME Boiler and Pressure Vessel Code Section II material that also meet the requirements of the listed ASTM specification may also be used.
ASME锅炉和压力容器规则节II材料也符合ASTM规格说明的要求，因此也可以采用。
Vessels used in liquid oxygen service should be designed according to ASME codes for the pressure and temperatures involved.
用于液氧设施的容器的设计要根据相关的压力和温度满足ASME的规范。
This procedure applies to all ASME Nuclear inquiries that are received by British Pipe Supports (JingJiang) Co Ltd.
本程序适用于英伦管架（靖江）有限公司收到的所有美国机械工程师协会（ASME）有关核问题的询价。
Familiar with ASME or other international standard is preferred.
熟悉ASME或其它国际标准者优先考虑；
It is not intended to replace or interpret the requirements of the ASME Boiler and Pressure Vessel Code (B&PVC).
它不是要取代或解释的ASME锅炉及压力容器规范（乙聚氯乙烯）的要求。
This paper introduces detailedly the boiler marking requirements in ASME specification including the items and location, etc.
ASME规范中关于锅炉规范标志（包括标志内容、标志位置等）的要求。
All CDI products are individually serialized and meet or exceed appropriate ASME and ISO standards.
所有CDI产品都单独标号，达到或超过ASME（美国机械工程师协会）和ISO（国际标准化组织）标准。
ASME formula is also performed to determine piping's capacity of self-compensation.
文中，ASME判断式被用于初步考察管系自补偿能力。
Valves are available in both flanged and butt welding ends. All conform to ASME specifications.
这些阀门都可配置法兰连接端口和对焊连接端口，都符合ASME标准。
Dimension A applies to drawing on page 9. Other dimensions for ASME Classes shown apply to these valves with DIN outside diameters .
尺寸A参见第9页的图。其它所显示的适用于ASME压力等级的尺寸也适用于DIN外径的尺寸。
Base on ASME B31 formula, with a pressure determine ratio which is repair factor ERF to estimated the extent of metal loss features.
基于ASMEB31的公式，用压力判定比即估计维修因子ERF表示金属损失特征的严重程度。
All butt welds shall be full penetration and done in accordance with ASME code.
所有对接焊缝应为全熔透焊缝并遵照ASME标准完成。
however , at an internal pressure above 3000 psi , the ASME Code , VIII-1 , requires that special design considerations may be necessary .
然而，以高于3000防扩散安全倡议的内部压力，ASME规范，第八-1，需要特别设计的考虑可能是必要的。
Watts self-closing combination T&P relief valves are design certified and listed by CSA and ASME.
美国瓦茨自动关闭组合式温度压力安全阀通过CSA和ASME的鉴定和认证。
Procurement of ASME Code Books as required per type of certification applied for.
根据所申请的证书类型购买相应的ASME标准书籍。
The new Control-Disk valve meets API, ASME and EN standards, making it suitable for use in all world areas.
新的控制盘阀满足的API、美国机械工程师学会和EN标准，使之适用于世界所有地区。
Journal of Heat Transfer; Transactions of the ASME.
传热杂志；美国机械工程师学会汇刊
Tank construction shall be of 300 pound test, 125 pound working pressure and be ASME stamped and National Board listed.
300磅实验压力和125磅工作压力检验，并应该拥有ASME（美国机械工程师协会）的盖章和美国国家委员会的认证。
According to ASME codes, stress evaluations under various service limits were performed.
最后，按照ASME规范的要求，进行了各种使用限制下的应力评定。
The ASME'S heat transfer calculation method for condensers has been presented.
介绍凝汽器ASME（美国机械工程师协会）传热计算方法。
The device shall be certified as meeting the requirements of ASME low pressure heating boiler code and ANSI Z21. 22.
这种装置应该经过认证并符合ASME低压加热锅炉规程和ANSIZ21.22的要求。
All welded heat exchanger tubing shall pass the flattening and flange test requirements of ASME SB-516.
所有的焊接式换热管应通过平整和法兰试验要求ASMESB-516。
Knowledge of PED and ASME, as well as Chinese standards for boiler industry.
熟悉PED，ASME等理念及锅炉工业方面的国标条列。
ASME is a well-known referenced standards of pressure equipments to enter North America and other countries need ASME.
ASME是对将进入北美市场或其它广泛认可ASME规范的国家的承压设备进行强制规范的知名标准体系。
ASME Document title, date and addendum number.
美国机械工程师协会（ASME）文件标题、日期和补遗号。
FEATURES AND METHODS OF HEAT RECOVERY STEAM GENERATOR ASME PTC4.
4余热锅炉性能试验规程的特点和方法。
American ASME vs European ISO vs China GB ?
美国ASME欧洲ISO中国GB标准比较
Be familiar with ASME and Chinese standard related to piping, pressure vessel and so on. Can find problems of piping and installation work.
熟悉ASME和国家关于管道施工、设备安装相关标准，能准确发现现场管道及设备安装过程中存在问题。
ASME American Society of Metals, U. S. A.
美国金属学会。
the Institute of Industrial Engineers (IIE); and the American Society of Mechanical Engineers (ASME).
他也曾担任工业工程师学会（IIE）和美国机械工程师学会（ASME）理事。
The design of noncircular section vessels is specified in ASME and GB150.
非圆形截面容器设计，ASME和GB150中有明确的规定。
For these certification items, ASME will confer 25 kinds of steel impression mark and the corresponding certification.
针对这些认证项目，ASME向世界范围内的生产企业授予25种钢印及相应的认证证书。
When the results of test meet the requirements of ASME Code, a WPQ will be prepared based on these test results.
如果试验符合美国机械工程师协会（ASME）规范要求，则应根据试验结果编制焊接程序检定记录。
john runs as fast asme.
约翰跑得和我一样快。
ASME does not "approve, " "rate, " or "endorse" any item, construction, proprietary device, or activity. ASME
不会“批准”、“评定”或“签署”任何条款、结构、专门的设备或行动。
Being familiar with state standards, rules and regulations of the industry as well as ASME specifications;
熟悉与行业有关的国家标准、法规，国外的ASME标准等相关规范；
