trunnion
美 ['trʌnjən] 
英 ['trʌnjən]
- n.【机】耳轴；空枢；炮耳
- 网络轴颈；枢轴；耳轴枢轴
词形变化
复数：trunnions
英汉解释
英英解释
例句
WILLIAMSONs metal to metal sealed trunnion ball valve is in general of the front ball sealing structure.
威廉姆森金属硬密封固定球阀一般采用球前阀座密封结构。
The trunnion assembly is supported by air bearings at the end of each arm and is held in position by brake shoes at each bearings.
耳轴组件的支承是每根臂末端的空气轴承，轴承上的闸瓦起定位作用。
In general, WILLIAMSONs trunnion ball valve features the front ball sealing design structure.
威廉姆森固定球阀一般采用球前阀座密封结构。
The load and air cylinder can swing round the pin in a plan, if the stroke is long, adopt the intermediate fixed or movable trunnion type.
负载和气缸可绕铰轴在一个平面内摆动，气缸长行程时，建议采用中间铰轴式
Trunnion design allows multi-directional flow; means that the valve is in no danger of being installed "backwards. "
耳轴设计允许多向流动，使阀门在“逆运转”时没有危险。
The showering trunnion mounting water cock, the choice is shorter, does not use the too long water pipe showering.
淋浴器安装节水龙头，选择较短，不用太长水管的淋浴器。
Special Trunnion sizes and configurations are available. Consult factory when ordering.
可提供特殊的轴径尺寸和配置，请在订购时咨询工厂。
and an adaptive curved cushion group is arranged between the trunnion ring retainer seats(3) and the converter shell seat(4).
所述托圈挡座（3）与所述炉壳座（4）之间还设置有自适应曲面垫组。
Handling and transport design of converter trunnion for Panzhihua ISC .
攀钢转炉耳轴的装运设计。
Trunnion Design: Upper and lower supports retain ball under pressure.
耳轴设计：在压力下上下支持阀球。
Application : Slag line of ladle , trunnion of converter and the line of EAF .
用途：用于钢包渣线、转炉耳轴及电炉的喷补。
The discharge trunnion liner, finally it finally fell to the ground and broke his leg.
跄，最后它终于跌倒在地，折断了腿。
screw yoke apart from the transmission output shaft and remove the trunnion cross.
从转换器输出轴移动螺杆套分离并拆下耳轴。
journal of the shock strut in the aft trunnion bearing(Fig. 408).
安装减震支柱后轴颈支耳到后轴颈轴承中（图408）。
The QTCV-T1 trunnion-mounted rotary control valve designed for general control valve service.
T1型装有底轴的旋转控制器是用来为普通控制阀服务的。
so that the shock strut will not touch it(Stage2, Fig. 405). Attach the trunnion link in position to clear the gear.
移开轴颈连杆，以避免减震支柱与之接触（图405，第2步），将轴颈连杆固定在一远离起落架的位置上。
The trunnion journal (22) is made by cutting hardened steel with using no cutting fluid.
该耳轴轴颈（22）通过淬火钢的干式切削形成。
support shaft(5) through the reaction link universal(3) and the trunnion link pin(6) from the aft side.
从后侧面，通过反应连杆万向接头（3）和轴颈连杆销（6）安装弹簧支撑轴（5）。
Refined Calculation on Tilting Moment for AOD Converter and Presentation of the Safety Position of the Trunnion
AOD炉倾动力矩精确计算及耳轴中心安全高度位置确定
Performance, reliability, and provision of the horizontal trunnion type
性能、可靠性和提供水平的轴径类型
Fitting up and welding technology of steelmaking converter trunnion ring
炼钢托圈的组对及焊接工艺
Dynamic load capacities for horizontal and trunnion type centrifugal casting machines are:
卧式和耳轴型离心铸造机的动态负载能力为：
Shipbuilding and marine structures; Trunnion pieces for span bearings and lead block bearings
造船和海上建筑物.跨架轴承和导向滑块轴承的枢轴配件
Processing Plan to Ensure Trunnion Co-axiality During Assembly Welding of Converter Trunnion Ring at Site
转炉托圈现场组焊保证耳轴同轴度工艺方案
Profile Modeling for Longitudinal Forward Kinematic Track of Push-arm Trunnion of Bulldozer
推土机履带台车架铰点纵前向运动轨迹的仿形
Trunnion mounts handle high differential pressures and prevent side loading
安装轴颈处理高压差并防止侧面负载
Design of Hydraulic Hoists for Eccentric Trunnion Sector Gates of Xiaolangdi Project
小浪底水利枢纽偏心铰弧形闸门液压启闭机设计
Repair and improvement to the trunnion on a cutter suction dredger
绞吸式挖泥船桥梁耳轴修复和改进
The Improvement of Turbine Guide Vane Trunnion Seal for Sanmenxia Water Power Plant
三门峡电站水轮机导叶轴颈密封改造
Measurement and Analyses for Trunnion Pin's Disalignment of Converter
转炉托圈耳轴同轴度的测定及其理论分析
Dynamic Analysis of Middle Axis of Double Ring- and- trunnion Universal Joint
十字环槽式双万向联轴器中间轴动力学分析
Improvement in technology of Large steel water pitcher trunnion
大型钢水罐耳轴的锻造工艺改进
Finite Element Analysis of Double Ring-and-trunnion Universal Joint
十字环槽式双万向联轴器有限元分析
Technology Development of Lower Trunnion Centre Drive and Its Application for Ljungstrom Air Preheater
空气预热器下轴中心变频驱动技术
FORWARD TRUNNION BEARING FUSE FASTENER;
前耳轴轴承保险紧固件；
Study and application of VSR technique on trunnion steel girder
支铰钢梁振动时效技术研究与应用
The study of riding comfort model of triple-axles truck with trunnion suspension
三轴平衡悬架载货汽车平顺性建模研究
Cracks Emergency Treatment on Trunnion and Mill shell
水泥磨中空轴及筒体裂纹的应急处理
Reparative try ofseriously damaged ball mill trunnion in Shaoguan Power Plant
韶关发电厂磨煤机轴颈严重损伤后的修复新尝试
Repair Welding of Converter Trunnion at Driven Side
转炉驱动端耳轴的补焊
