meshing
美 [meʃ] 
英 [meʃ]
- n.网；网眼；筛孔；网丝
- v.【机】(使)咬合；编[织]网；使成网状；用网捕
- 网络啮合；网格划分；相合
词形变化
复数：meshes 现在分词：meshing 过去式：meshed 反义词
同义词
英汉解释
n. | 1. 网眼;筛孔;网,网状物,网络;网丝;铜纱;法网 |
v. | |
英英解释
例句
Once you get a decent low density point cloud, you are ready to move on to denser point cloud and the meshing steps.
一旦你得到一个体面的低密度点云，你是准备进入更为密集的点云和啮合步骤。
Once your point cloud is free of obvious noise, you are ready to run the Meshing steps to triangulate it.
一旦你的点云是显而易见的，无噪音，你就可以运行它三角啮合步骤。
Repeat the process for the rest of your noise points and then move on to the Meshing steps, described in the section below.
重复该过程为您的噪声点休息，然后移动到啮合的步骤，在下面一节中描述。
It should be said GALLUS machine meshing gear teeth, there was a small staves of opportunities.
不该说GALLUS的机械是歪齿轮啮合的，呈现齿杠的时机小。
The meshing contact-impact and contact performance of spiral bevel gears has a strong impact on the whole machine performance.
螺旋锥齿轮的啮合接触冲击特性和动态接触性能的好坏严重影响其整机的工作性能。
Conjugate conditions equations are established on the basis of conjugate conditions of two curved surface and meshing theory of gears.
根据两曲面的共轭条件和齿轮啮合原理得到齿轮共轭的共轭条件方程；
With a two-stage gear system with time-variant meshing stiffness taken into consideration, the paper established its dynamic equation.
在考虑二级齿轮传动系统时变啮合刚度的情况下，建立了其动力学方程，它是一个具有周期性时变系数的线性动力学系统。
Checking the transmission chain rotation is normal or not, ensure its without extrusion, Chain and sprocket meshing good.
检查传输链条转动是否正常，保证其无挤压、受卡现象，链条与各链轮啮合良好。
Toothed ball meshing, compact structure, rational design, achieving the mechanical transmission precision requirements.
球齿式啮合，结构紧凑，设计合理，达到机械传动精度的要求。
The meshing of her public and private lives placed near schizoid demands on Thatcher.
她的公共和私人生活的不同要求简直会让人神经分裂。
It is proved that the main source of the noise was the meshing vibration of reverse gears in gearbox.
综合分析了实测信号及其数据处理结果，得出此型号拖拉机发生异常噪声的主要原因是其变速箱倒档齿轮的啮合振动所致。
A well solved DSM looks like this: If your point cloud has noise points you may want to remove the noise points before meshing.
一个很好的解决用电看起来像这样：如果您有噪声点云点您可能需要删除之前的噪声点啮合。
Rotational speeds, meshing forces, and meshing frequencies of the gears are obtained by dynamic simulation of the virtual prototype.
对虚拟样机模型进行动力学仿真，得到各级转速、齿轮啮合力及啮合频率。
On the premise of considering boundary condition, meshing performance of the single-enveloping of TI worm gearing is carefully studied.
在考虑边界条件的前提下，深入分析了一次包络TI蜗杆传动的啮合性能。
An involute gear may be defined by its meshing with a rack with straight-lined flanks.
一种渐开线齿轮可界定其与齿条啮合与直排两翼。图。
One troublesome task involves meshing the mundane but incredibly complex machinations of accurately billing cell phone subscribers.
其中一个看似简单但其实复杂的任务就是如何对手机用户准确收费。
This design method is easily performed. Furthermore, only involving the plane meshing theory, the result is clear and is easily tested.
这种设计方法简单可行，只涉及到平面啮合理论，结果直观，便于检验。
Holes in parallel between the degree of error will affect the quality of the meshing gears.
孔系之间的平行度误差，会影响齿轮的啮合质量。
Because when the frequency of close to the meshing of gears susceptible to the natural resonance frequency.
因为当啮合频率接近于齿轮系的固有频率时容易发生共振。
Gear meshing process as a contact, because involves contact state changes a complex nonlinear problems.
因涉及接触状态的改变而成为一个复杂的非线性问题。
Two main sources of noise and vibration can be considered: pressure and gear meshing.
噪声与振动的两个主要来源可以被视为：压力作用与齿轮啮合。
The gear teeth and meshing line are distorted in the meshing process as a result of wearing and rise in temperature.
实际应用中，由于磨损和受热等原因，使得齿轮齿廓以及啮合过程中啮合线都发生了畸变。
Results Treating the problem using an image-based meshing approach is remarkably straightforward, robust, accurate and efficient.
结果采用一种基于图像的网格方法来处理问题是非常先进的，也是非常精确有效的。
Finite Element Method has its problems: meshing is not much fine, the boundary condition is not so rational and etc.
这既有有限元计算方法本身存在的问题，如网格划分不够精细，边界约束条件不是非常合理等；
Sometimes the meshing of ideals, etc. is really easy, other times not so much.
有时候，理想啮合，等真的很容易，与其说其他时间。
The special meshing of convex and concave teeth profile makes the relative radius of curvature of the contacting point longer.
独特的凸凹啮合齿廓，使两齿轮在接触点处的综合曲率半径较大。
In the proposed approach, the gear meshing frequency was acquired by chirplet path pursuit, and then the speed signals could be got.
该方法先采用线调频小波路径追踪算法提取齿轮的啮合频率分量，由此得到转速信号；
Worm gear and worm drive, meshing gear meshing of the relative speed between sliding friction loss is big, so, the low efficiency.
蜗轮蜗杆啮合传动时，啮合轮齿间的相对滑动速度大，故摩擦损耗大、效率低。
Principles and thinking of DEM was creatively introduced into dynamics analysis of the gear meshing rotor system.
创造性的把DEM的原理和思想方法引入到齿轮啮合转子系统的动力学分析中。
The results show that it is feasible to apply interval meshing technology to composite sabot of high power armor piercing projectiles.
结果表明在大威力穿甲弹复合材料弹托上应用间隙啮合技术是可行的。
The tooth shape, meshing and processing technology, are more complicated than ordinary gear.
其齿面形状、啮合状态及加工技术等都比一般齿轮复杂的多。
Directional decomposition algorithm and meshing method are two key factors in extraction of directional feature.
网格技术和方向分解是网格方向特征的两个关键技术。
According to the BEM grid convergence analysis, the accuracy of a numerical result relates to the meshing density.
根据边界元数值方法的网格收敛性分析，计算结果的精度与网格疏密度有关。
The results of modal analysis and dynamic simulation of meshing are used to solve the dynamic response.
利用齿轮箱模态分析结果和动力学仿真得到的啮合激励求解该系统的动态响应。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
Last month, a resurgent Nomura completed meshing the systems that underpin its operations with those of Lehman.
上个月，野村与雷曼的业务支持系统完成了整合，一个全新的野村由此诞生。
In transmission, the derivation of meshing points is researched by two ways, which are meshing theory and surface interference.
在齿轮传动过程中，分别利用啮合理论和曲面干涉的方法，对接触点和接触迹线的求解进行了研究；
Mathematicl model of the steady temperature field is established by combined research of heat transfer, tribology and meshing theory.
通过蜗杆传动的传热学、摩擦学及啮合原理的结合上进行研究，建立了蜗轮稳态温度场的数学模型。
Beginning from eliminating the influence of T- vertexes around shadow boundary, this paper proposed a new meshing algorithm.
本文从消除T型结点对图形计算的负面影响入手，提出了一种新的快速网格化算法。
gear will have an impact in the meshing process, the shock pass through the shaft and bearing to the gear box, which cause the vibration.
齿轮在啮合过程中会产生冲击，冲击通过轴和轴承传递到齿轮箱体上而引起箱体振动。
